Expert Answers about Chevrolet Living Room Accessories
- Weight of Aries Bull Bar for 2014 Toyota 4Runner
- The Aries Bull Bar with Removable Skid Plate that fits a 2014 Toyota 4Runner weighs 25 lbs so it is not a heavy accessory at all. It will protect your 4Runner's front end without any type of negative affect on tire alignment. The bull bar comes in two different colors for you to choose from.
- Black Powder Coated Steel: Aries Bull Bar with Removable Skid Plate # AAB35-2006
- Polished Stainless Steel: Aries Bull Bar with Removable Skid Plate # AA35-2006
The only other thing you might...
view full answer... - Clearance Between Vehicle Sunroof and Roof Rack Crossbars of Inno Square Bar Roof Rack
- Roof rack makers generally do not recommend operating a vehicle's sunroof when an aftermarket roof rack is installed. Even if there is no clearance issue between the bottom of the crossbars and the top of the sunroof there would be a lot of noise from wind turbulence at the bars that would likely make you want to keep the sunroof closed anyway.
Also note that any roof-rack-mount accessory item you might install on the crossbars - say a bike rack or cargo carrier - will use some type of...
view full answer... - How to Determine Clearance Required for Hitch Cargo Carrier on 2007 Jeep Wrangler
- It is easy to figure whether a hitch accessory like the etrailer Cargo Carrier # e98874 will fit well at the rear of a vehicle like your 2007 Jeep Wrangler that has a rear-mounted spare tire. All you need to do is take one simple measurement. Please refer to the linked article which shows how to measure from the hitch pin hole to the rear edge of the spare. This measurement tells you the clearance you need from the accessory carrier.
The etrailer Cargo Carrier # e98874 will need just over...
view full answer... - Ground Clearance with a Trailer Hitch Installed on a 2013 Volkswagen Beetle Convertible
- I have included a picture showing Curt trailer hitch # C11354 installed. As you can see the top of the receiver is about an inch or so from the bottom of the rear fascia. The bottom of the receiver then is another 1-1/2 to 1-3/4 inches below that. Your 2013 Volkswagen Beetle Convertible already sits pretty low leaving not much room for a hitch. While I don't have an exact measurement of the ground clearance the picture certainly tells the tale.
If you want to use the hitch for an accessory...
view full answer... - Storage Cover for 2018 Lance Model 1995 Travel Trailer
- The makers of RV storage covers are familiar with all of the accessory items commonly installed such as roof-mounted vents and AC units, spare tires and ladders. The presence of these RV features is taken into account. Please refer to the linked diagram to see how to measure for your cover.
In addition to choice of cover size you'll want to consider the climate in which the travel trailer will be stored as we have covers optimized for specific climates. On the main page for covers that...
view full answer... - Dimensions Of The Mountain Top EVO-M Retractable Hard Tonneau Cover
- The Mountain Top EVO-M Retractable Hard Tonneau Cover with T-Slot Accessory Rails # MNT56FR rails are 2-1/8" tall, so you'll need to measure your backrack tonneau cover adapter to ensure they'll fit inside of it.
The canister is 8-3/8" tall x 9-1/8" wide, so you would need to measure how much room you currently have with your Decked drawer system to know if the canister will be a compatible fit.
view full answer... - Recommended Hitch for a 2023 Kia Sportage
- If you are in the area of Wentzville MO 63385 we do provide installation services. You would need to contact customer service to get on the schedule. If you live outside of this area we do have a network of reliable installers all over the country. You will want to go to the left hand side of the Item # C94WR product page. Underneath the installation videos is a blue link that says Locate installers near me. You will want to input your zip code to access the list of installers.
There...
view full answer... - Ground Clearance Measurement on 2017 Hyundai Santa Fe Sport with Curt Class III Trailer Hitch
- When we installed the Curt Class III Trailer Hitch Receiver # C13152 that you referenced on a 2016 Hyundai Santa Fe Sport, we found the inside top of the receiver to the ground measured 13 inches. I've attached a photo showing this measurement for you.
For the vehicle we installed the hitch on, from the bottom of the hitch receiver to the ground would measure 10-1/2 inches. These measurements will help give you a good idea of how far off the ground your hitch receiver will sit.
I can't...
view full answer... - Distance From Gooseneck Ball to Back of B&W Companion 5th Wheel Trailer Hitch w/ Slider
- The B&W Companion 5th Wheel Trailer Hitch w/ Slider # BWRVK3400-5W referenced in your question will have a distance of 15 inches from the center of the gooseneck ball to the back edge of the Companion. The overall length of the 5th Wheel Hitch is 45 inches and has a width of 34-3/8 inches. If you are checking for clearance with a bed mounted accessory like a toolbox, you will just want to measure this 15 inch distance out from the center of your gooseneck ball to see if it will fit.
This...
view full answer... - Recommended Weight Distribution System for a 3,500 lbs Airstream Trailer
- I understand your concerns and I'll be happy to help you. You have a lot of truck and not much camper. From what I can find it looks like a 16' Airstream trailer tops out around 3,500 lbs. The Gen-Y Torsion 2-Ball Mount item # 325-GH-1324 you were looking at will do a great job of absorbing road shock and bounce but it will not address sway in any way.
Since you're worried about sway, I recommend adding a weight distribution system to your set up. This would keep your trailer in line...
view full answer... - Platform and Cargo Basket Options for Thule TracRac One and Thule Wing Bar Evo
- I do have a solution for you but unfortunately the Rhino Pioneer Platform Rack 76inch x 54inch is not compatable with either your Thule TracRac One or Thule Wing Bar Evo as it requires its own vehicle mounting system.
The Rhino-Rack Universal Pioneer Platform 58inch x 47inc part # RR42115BF will fit on your Thule TracRac One or your Thule Wing Bar Evo. Also Two of the Yakima SkinnyWarrior Cargo Rack part # Y07014-16 with extension will fit your Thule TracRac One, and will fit without...
view full answer... - Exact Measurement of Receiver of Curt Trailer Hitch 15703
- I went out to the warehouse with digital calipers to get the exact measurement of the receiver of the Curt Trailer Hitch # C15703 and found it to be 2.55" though it is possible for the hitch that is shipped to you to have slightly (and by slightly I mean a couple hundredths or thousandths of an inch) more or less room in the receiver.
There is always going to be some slight play but you can reduce this with the use of the Blue Ox Hitch Receiver Immobilizer II # BX88225 which is designed...
view full answer... - Distance From Hitch Pin Hole to Curve in Shank on Reese Weight Distribution Shank # RP63971
- The shank you referenced, Reese Weight Distribution Shank # RP63971, is intended for use in the drop position only with their weight distribution systems that use either round or trunnion spring bars. I pulled a sample of the Reese shank # RP63971 to take the measurement you requested. As shown in the linked photo that I prepared for you, the distance from the center of the hitch pin hole to the point on the shank where the curvature begins measures 3-1/2-inches.
Unless you are using such...
view full answer... - Hitch Pin Location for Curt and Draw-Tite Trailer Hitches on a 2022 Ford Bronco
- The center of the hitch pin hole for the Draw-Tite Max-Frame Trailer Hitch Receiver # DT37GR is 6" further out than the center of the hitch pin hole for the Curt Trailer Hitch Receiver # C76WR. Since the hitch pin hole determines where your accessory will be sitting this is the dimension you want to take note of as opposed to the end of the receiver tube.
I went and measured the Curt hitch and from the outermost mounting plate that installs on your 2022 Ford Bronco to the center of the...
view full answer... - Will a Generator Carrier Fit on the Bumper of Our 2020 Coachmen Leprechaun with Flat-Tow Accessories
- In order to confirm whether you can fit a generator carrier on your back bumper of your 2020 Coachmen Leprechaun, it really depends on the dimensions of your rear bumper. I went ahead and did some research on your vehicle, and I discovered that the width of all options of the 2020 Leprechaun have an exterior width of 100 inches. Another relevant dimension is your towing equipment that you are using to flat-tow your jeep wrangler.
With that being said, I recommend the Mount-n-Lock GennyGo...
view full answer... - Hitch Pin Hole Center to End of Shank Distance of Hollywood Racks HR4000 Destination 4-Bike Rack
- On the Hollywood Racks Destination 4-Bike Rack, part # HR4000 the distance from the center of the hitch pin hole to the end of the shank is 2-1/8 inches, as shown in the provided photo. Since the depth of your receiver tube is 2.6 inches, measured from the center of the hitch pin hole to the rear of the receiver, the Destination will fit in your hitch receiver with a little bit of room to spare.
view full answer... - Mounting Dimensions for the Dutton-Lainson Trailer Winch # DL14881
- I went out to our warehouse and measured the mounting base for the Dutton-Lainson Trailer Winch, item # DL14881. The flat part of the base measures 8-3/8 inches long by 5 inches wide. The elongated bolt hole at one end of the winch is 1-7/8 inches long and the 4 elongated holes at the other end are 1 inch long. The two round holes are 3/8 inch diameter. The distance on center between the long elongated hole and the first set of shorter elongated holes is 4-1/8 inches. The distance between...
view full answer... - Can Curt Multipurpose Ball Mount be Used for Bike Rack Between Car and Travel Trailer
- So long as you have the needed space between your RAV4 and travel trailer for your bike rack and trikes to fit you can use the Curt Multipurpose Ball Mount with 2" Receiver for Bike Racks and Cargo Carriers # D210.
There's no way for me to know how much room you have or if you have the needed space so you'd need to take some measurements, of course, and the # D210 extends 12-1/2" from the hitch pin hole to the hitch ball. This ball mount - when you are towing and using an accessory at...
view full answer... - Sport Trailer With 15 Inch Hitch Ball Height
- I have a great option that is going to work for you, though I checked with Yakima, and to use the Rack and Roll Trailer # Y08107 the top of the hitch ball must be 22" off the ground. An inch or two in either direction would work, but the seven inch difference you have would make the trailer susceptible to fishtailing due to the uneven tongue height.
With that said, there is a similar trailer that is going to work very well for you, the Malone MicroSportXT Trailer # MPG460XT, which requires...
view full answer... - Weights and Measures of Demco HiJakcer 5th Wheel Trailer Hitch for a 2016 GMC Sierra 2500 Short Bed
- For Demco Hijacker Autoslide 5th Wheel Trailer Hitch w/ Slider - Single Jaw - Underbed - 18,000 lbs Item # DM8550022 the head by itself, which is # DM6081, weighs approximately 65 pounds. The base the head sits on by itself weighs approximately 178 pounds. And the side plates weigh about 40 pounds. They combine for a total weight of approximately 285 pounds.
The base is 35 inches long by 33 inches wide overall.
According to our contacts at Demco the pin box should NOT make contact with...
view full answer...
Go To Results